iiinova — where your digital self keeps evolving

NessoAsks @nessoasks.bsky.social · 05/10/2026

Are my photography skills progressing, or becoming increasingly unhinged? Is it a both-and situation? #Maker

A workshop, with a light brown workbench in the center. Leaning against the left side of the workbench with only two of its legs touching the floor is a black camera tripod, with the camera pointed down towards the workbench.

To the right of the workbench, standing on a blue card table, is a production light on its own black tripod. The light is also angled down toward the workbench.

On the workbench, itself, is a large piece of paper that's been partially unrolled.

NessoAsks @nessoasks.bsky.social · 03/10/2026

The PR of Theseus: when the feedback on the PR leads you to change every line of the PR and ask, "Is it still the same PR?" #IYKYK #ShipOfTheseus

010

NessoAsks @nessoasks.bsky.social · 09/09/2026

No progress pic today as I'm editing the last pieces of the video together. Now: "I think I have everything." Later: "No, wait - I need THAT shot. Ok now I have everything." Even more later: "No, wait..." #Maker

020

NessoAsks @nessoasks.bsky.social · 07/09/2026

Just hang it! To put the piece up, I used two upside-down picture hooks on each side of the frame and looped picture wire through to hooks screwed into the joists. The piece is now done! I hope to get the full build-video out this week yet. #Maker

A view of the side of the piece I'm working on, showing two picture hooks attached upside-down. There is a piece of gray picture wire that runs through both hooks and goes up out of the picture.

The frame itself is black, with one of the stainless steel screws and finishing washers on the left. To the right is the white wall of my workshop.

000

NessoAsks @nessoasks.bsky.social · 04/09/2026

Well, THAT didn't work. I think the hole for the heat-set insert was too small, so when I pressed down with the soldering iron it melted too much of the plastic around it and it came rushing up through the middle. Time for another #FreeCad tweak! #Maker #3DPrinting

Part of the white electronics box is lying on a scratched, dark grey work surface. In the center are two mounting holes with brass heat-set inserts in the middle. Both inserts are embedded into the mounting posts, slightly off-center, and partially filled melted PLA plastic.

230

NessoAsks @nessoasks.bsky.social · 02/09/2026

RE-boxing pic! I revised the electronics box to better accommodate the USB Power inputs: * Nudge the existing post to the right * Add a post for the second * Shrink both to take an M2 heat-set insert; the holes were too small for the M3 screws used everywhere else. #Maker #FreeCad #3DPrinting

A white, rectangular, 3D-printed box sits on a dark grey work. The box is roughly 10cm x 20cm, with 2cm tall walls. The box has two full walls, and most of a third. The cables for both power inputs and the Lumidrive will all connect on the left side, so there is no left wall.

Inside the box are three holes at the bottom, used to mount the box to the larger piece.

Also inside the box are 5 mounting posts scattered around, used to secure the electronics to the box. Four of them are 8mm tall, but the fifth is 12mm. All five have their centers partially hollowed out to accept a heat-seat insert (which have not been inserted yet). The two posts on the far left are highlighted with an orange rectangle - these are the two that the USB power inputs mount to.

071

NessoAsks @nessoasks.bsky.social · 31/08/2026

Power up! The software issues I was troubleshooting last week turned out to be primarily a power issue - or rather, the LACK of power. I added a second USB Power Unit dedicated to the rim lights, and that solved everything. #Maker

A white, open-top box packed with electronics sits on a light brown plywood background. Inside the box there is a red Lumidrive, a black FeatherWing latching relay, and two black USB power units. The power units each have a USB-C cable connected, going to the left, out of frame.

000

NessoAsks @nessoasks.bsky.social · 26/08/2026

No pic today as I'm working through a mix of software and hardware problems, trying to tease them apart. It's funny that solving a technology problem so often requires getting it to fail *reliably*.

000

NessoAsks @nessoasks.bsky.social · 24/08/2026

We'll be coming around the mountin'! I got the rest of the components mounted to the backboard this weekend. I think I have all of the internal hardware in place now. The software is giving me some grief, so that's next. #Maker

On the right is the edge of one of the white 3D-printed towers with its custom bracket. There is a black screw anchoring it to the light brown plywood backboard.

In the foreground is the edge of the electronics box, again, anchored with a black screw. The barest sliver of the red Lumidrive is visible at the very bottom, and the black USB power supply on top of that. A black USB-C power cable is hooked into the latter, and goes up and off the right, out of frame.

In the upper left corner of the shot there is a black wire clamp, attached to the backboard with more black screws, holding the USB cable in place.

000

NessoAsks @nessoasks.bsky.social · 21/08/2026

Hardware delivery! I found these 4mm diameter pipe clamps at Lowe's that I'll use to wrangle and secure the growing collection of wires I have inside the box. So many wires. #Maker

Several black wire clamps lay on a dark grey work surface. There is a single clamp in the foreground, and a small pile of them in the background. The clamps have two mounting holes, one on either side of a 4mm semi-circle where the wires will run.

001

NessoAsks @nessoasks.bsky.social · 19/08/2026

The old tower (first pic) had the tabs that prevent the tower walls from going all the way up, so light was escaping and creating the "halo" (shown with the orange rectangle). The redesigned tower successfully eliminates the halo. One more problem solved! #Maker

A closeup of the front of the piece I'm building. On the right side of each picture is part of one of the circles that light up. Extending to the left is part of the "straight" sections.

The old version of the tower had a tab that stuck up, and let light escape. That light formed a halo in the straight section, shown here surrounded by an orange rectangle.

020

NessoAsks @nessoasks.bsky.social · 17/08/2026

I redesigned the towers (again). The latest version raises the top to remove the tabs which should eliminate the light seepage. I also added mounting brackets. I *think* this is the final version. (At least until the next version comes out.) #Maker #FreeCad #3DPrinting

The tops of two white 3D-printed towers are shown on a dark grey work surface. The towers are covered in a white diffusion film.

The tower on the left shows an alignment tab that sticks up 1mm from the rest of the tower. The one on the right has a flush top, so does not have the tab at all.

171

NessoAsks @nessoasks.bsky.social · 14/08/2026

3/3 My solution was to use one pair of lever wire connectors mounted to the frame, and another mounted to the base. Between those is a lot of extra wire, formed into a simple spring. Now when you open or close the lid, the wires in the middle flex, while the others are locked in place. #Maker

010

NessoAsks @nessoasks.bsky.social · 14/08/2026

2/3 The lights around the rim come together where the frame and backing hinge. Power was going to come from the electronics mounted to the base, which meant I needed a connection that would flex when the case was opened, and not rip or torque the LEDs. #Maker

110

NessoAsks @nessoasks.bsky.social · 14/08/2026

1/3 The pre-bent wires I showed last time can be seen at the very top, joining the rim lights to the lever wire connectors. It was very tight, cramming all of that into a corner, but it worked. #Maker

The inside of a very shallow frame is shown, with a piece of acrylic attached, forming a lid. Going around the inside of the frame are two strips of LEDs, almost coming together in the corner.

In the very corner, however, is a pair of grey and orange lever wire connectors, with red and white wires leading to the ends of the LED strips.

On the light brown plywood base is another pair of the same wire connectors, also mounted. These have red and white wires going out of the lower right corner of the picture.

Attaching the two sets of wire connectors is another set of red and white wires, looping back and forth a couple of times. These "middle" wires create a loose spring, and allow the case to be opened without damaging the electronics or LEDs.

110

NessoAsks @nessoasks.bsky.social · 12/08/2026

I'm back to pre-bending wires again. This only happens when I'm working in tight spaces, and once I realized I could do this on the Dr. Theopolis build, it's becoming my go-to solution. I have more tools in my toolkit than a hammer, I swear! #EverythingLooksLikeANail #Maker

On a dark-grey, and very scratched-up work surface, are 4 small pieces of 18-gauge wire, pre-bent to fit snugly into a corner of the frame of the piece I'm building. The top two pieces are white, and the bottom two are red. All of them have had their ends striped to reveal the solid copper.

010

NessoAsks @nessoasks.bsky.social · 10/08/2026

I pivoted again on the issue of lighting, this time opting for a line of LEDs attached to the inside of the frame to simply flood the inside with light. This solves one problem and creates another, unfortunately. Trusting the process, but tripping on the speed bumps. #Maker

The inside of a very shallow frame is shown, with a piece of acrylic attached, forming a lid. Going around the inside of the frame is a strip of LEDs. The corner of the frame is show, and the LEDs hug the 90-degree bend.

The LED-strip is white with a yellow diffusion covering over the LEDs themselves. The copper pads for Ground and Voltage can be seen every so often.

020

NessoAsks @nessoasks.bsky.social · 07/08/2026

Good news: I've been able to check off some of my "Problems to Solve". Bad news: I've had to add problems to the list. #Maker

A notebook sits open on a light brown desk. The page shows several problems, each with their own checkbox. About half of the problems are checked off.

020

NessoAsks @nessoasks.bsky.social · 05/08/2026

Good news: I got the electronics mounted back in the box. Bad news: I added the relay directly above one of my mounting points, so I can't use it. Go ahead, say it - I have a screw loose. #Maker

On a piece of light brown plywood sits a small white box. In the box is an electronics package consisting of a red LumiDrive, a black USB power supply, and a black Featherwing latching relay.

In the lower left corner, the USB power cord extends out of frame. At about the middle of the picture, a white alligator clip connects to the ground wire of the power supply, and extends out of frame.

Some blue painter's tape appears in the lower right corner, holding the USB cable in place so it doesn't torque the electronics.

020

NessoAsks @nessoasks.bsky.social · 03/08/2026

I added a Featherwing latching relay to the electronics package for this piece which will allow me to turn some of the LEDs on and off via software. Yes, I just re-invented the light switch. In my defense, the relay makes the most satisfying click when it switches. #Maker #ASMRElectronics

On a dark grey non-static work pad sits a red LumiDrive, with a USB-C cable coming out of its port on the left. Above and to the left of the LumiDrive is black USB power supply.

Above and slightly to the right of the LumiDrive is a black Latching Relay Featherwing.

There are several wires (red, white, blue, and green) connecting these three components together.

At the extreme top is a black multimeter probe, currently connected to a white wire stick up and out of frame.

010

NessoAsks @nessoasks.bsky.social · 31/07/2026

The beacons are lit! I got all three LED rings wired in, and I'm happy to report that I didn't use a single alligator clip this time. #Maker

On a light brown plywood back lie three 2-inch LED rings, wired up in series, going from the foreground to the background. The rings are lit up with a rainbow of colors.

In the extreme foreground sits the red Lumidrive and USB power input that drive the rings.

The Lumidrive is connected to the first LED ring with a series of four grey and orange lever wire connectors.

010

NessoAsks @nessoasks.bsky.social · 29/07/2026

It's time for a side quest! FIVE side quests, actually. My intended next step was to mark out where the LED trenches would be placed in the plywood backing, but I accumulated several unanswered questions of how things were going to actually fit together. I made a list. #Maker

A notebook lies on a dark grey work surface. The notebook is open to a page which has a title of "Problems to Solve", with five questions:

* How to run the wires to connect the 3 towers?
* How to align the trenches so they line up with the front matte?
* Will I see a good diffusion of the light?
* Will there be any shadows to address?
* How will I attach the towers to the bases?

By each question is a red checkbox, currently unchecked. Under each question are some notes about how I think I can solve the problem.

010

NessoAsks @nessoasks.bsky.social · 27/07/2026

I attached the LED strips I prepared to the inner track of the "ledges", which will sit down in the trenches (not shown). Because the strips are oriented vertically, I can bend them around the curve of the ledge smoothly. #Maker #3DPrinting

On a dark grey work surface lies a white, 3D-printed piece, shaped like a letter "J". The cross-section of the J is an upside-down letter "L", so the top forms a ledge.

Attached to the bottom of the piece is an LED strip, attached to the "J" vertically via an adhesive. The LED strip has a white backing, with copper pads between each LED on the strip. The LEDs are covered by a yellow film that diffuses the light.

On the left of the picture, two wires (one red and one white) are shown soldered to the end of the strip. The wires are bent at a 90-degree angle, pointing to the "inside" of the letter "J".

030

NessoAsks @nessoasks.bsky.social · 24/07/2026

To prepare the LED strips, I've surface-soldered wires to one end of each strip. I've pre-bent the wire to form a 90-degree angle to the strip so that when attached they'll go "down" and away from the line. (The reason for that will make more sense in an upcoming update.) #Maker

Two pieces of LED strip are shown, partially curled up on a dark grey work surface. Each strip has two wires soldered onto the ends - one white and one red. The wires are bent at a 90-degree angle so that if the strip is laid flat on the table with the LEDs facing down, the wires would go straight up.

A close-up of one of the LED strips partially curled up, laying on a dark grey work surface. This shows how the two wires (white and red) soldered onto the ends, and bent down and away from the strip itself.

020

NessoAsks @nessoasks.bsky.social · 22/07/2026

I'll be attaching a single strip of LEDs to the three pieces of ledging that make up the inside curve of the trench (shown dry-fitted on the right). To hold everything together temporarily, I've attached the three pieces with painter's tape (left side). #Maker #FreeCad #3DPrinting

The picture features two curved pieces of white 3D-printed "trench". Each piece looks like an upside-down letter "J" (or an all white candy cane).

The one on the right has just the trench, plus the three pieces of "ledge" that form the inside of the curve.

The one on the left is just those three pieces of ledge, attached on the inside with blue painter's tape.

030

NessoAsks @nessoasks.bsky.social · 20/07/2026

I did a dry fit of the trench "ledges" that will be used to suspend the diffusion film above the LED strip. Didn't quite get the measurements perfect where the bases come together, though. I think I can still work with that. #Maker #FreeCad #3DPrinting

A shot looking down at both trenches laid out on a dark grey work surface. When assembled as shown on the right, the trench will look like a white letter "J", with four small, square, mounting posts at various points around the outside.

The trench on the left has all of its components pieces laid out - the two pieces making up the base of the trench are in the center, and the six pieces that form the "ledges" where the diffusion film will be suspended. These six pieces will be mounted vertically along the inside of the trench base.

A close-up of where two sets of the ledges come together. One set is a millimeter higher than the other set.

040

NessoAsks @nessoasks.bsky.social · 17/07/2026

I didn't start out trying to create a knolling pic, but here we are. I got all pieces of both trenches printed. Now I just have to clean them up. Ugh. #Maker #FreeCad #3DPrinting

On a dark grey work surface are two sets of white, 3D-printed parts. Some are curved and some are straight. Some of them have the cross section of a trench, while the rest are "shelves" that will fit down into the trench, and allow me to suspend a piece of diffusion film across the top.

071

NessoAsks @nessoasks.bsky.social · 15/07/2026

The trench, version 2. Aside from being nearly twice as wide, I printed these white to better reflect the light and added the mounting holes. Each of the white sections is Part 1 of 3. I hope to have the other two pieces designed and printed by the end of the week. #Maker #FreeCad #3DPrinting

On a grey work surface are four pieces of 3D-printed "trench". On the left are the two original v1 prototypes, printed in grey. One is a straight piece laid out horizontally on the works surface, nearly 20cm long, 1.8cm wide with 1mm walls. the other piece on the left has the same basic dimensions, but is curved to look like the letter "J".

On the right are the version 2 iterations, printed in white. All of the dimensions are the same except the width - they are nearly twice as wide. These also have small tabs that protrude from the main structure. Each tab has a hole in it. These will be how I attach them to the rest of the piece.

020

NessoAsks @nessoasks.bsky.social · 13/07/2026

I need the LEDs to form a smooth curve, so I created these frames in #FreeCad. The LEDs will sit down in this "trench", along the inside wall. This first version is too narrow, though. I'll need to make them wider to let more light through. That's why we prototype, kids! #Maker #3DPrinting

An oblique shot of a grey, 3D-printed trench sitting on a dark grey work surface. The trench is nearly 10mm wide at the base and has walls that are 20mm tall. The trench is curved 180 degrees, forming a half-circle, with one end extending off out of frame to the right.

040

NessoAsks @nessoasks.bsky.social · 10/07/2026

I found a different LED strand, this one has clear points to cut and reconnect it, and it has a diffusion layer built right in. It's also much brighter than the previous. I still have some work to do, but this gets me closer to a final solution. #Maker

A split image.

On the left is a strand of LEDs, lit up in a yellowish-white, laying on top of a light brown workbendh.

On the right is the same strand, unlit. A portion of the strand is facing the camera in the foreground, showing repeating segments, designed to allow you to cut the strand to length.

Each segment is denoted with a vertical line, partially visible. This is the line that you would cut the segment to length. On each side of every segment are copper pads - points where you would solder wires to complete the circuit. On the tops of each segment are "+5V" (plus 5 volt) pads, and on the bottoms are "GND" (ground) pads.

in the background is more of the LED strand, coiled up on a light brown workbench.

000

NessoAsks @nessoasks.bsky.social · 08/07/2026

I figured out how to wire the LED rope, but this was as white as I could make it. Additionally, when I cut it, there was no clear way to attach new leads. I should have researched it better and gotten cuttable AND connectable rope. #Maker

A light brown work bench is partially in the upper left corner by a dark grey work surface. On the work surface is a length of coiled LED rope, lit up in a light blue. Going off to the right are four alligator clips powering the rope - white, green red, and black. The alligator clips are taped down with blue painter's tape so they don't accidentally move and short each other out.

000

NessoAsks @nessoasks.bsky.social · 06/07/2026

I need to make a couple of turns with the LEDs. But as you saw in the last progress pic, wiring up segments of LED strips would leave a broken-up look. LED neon "rope" gives a smoother look, so I think I need to pivot. Now I just need to figure out how to wire them up to the Lumidrive. #Maker

A string of lavender LEDs, encased in a white diffusion sleeve, is curled up and sitting on top of a dark grey work surface.

000

NessoAsks @nessoasks.bsky.social · 03/07/2026

I need to create curves with LEDs. My original plan was to use daisy-chained segments of LED strips. That would lead to segments of light, defined by the length of each strip (left), even when under a second layer of diffusion film (right). I need a different solution to smooth out the bends. #Maker

A split photo.

On the left is a small strip of LED lights on a work surface, lit up in a light purple. The wires for the lights are coming out above it, and are connected by alligator clips to the power source (not shown). An orange curly bracket was added to the photo, illustrating where the light stops on each end of the strip.

On the right side is a red light source under a layer of diffusion film. The film is suspended in a circular "tower" that sits on top of the light source. The effect is a red circle with a more intense red oval in the center. The light source is the same small strip of LEDs. The wires for it are shown coming out of the tower on the top.

010

NessoAsks @nessoasks.bsky.social · 01/07/2026

With a little help from my younger kiddo, I got the other two bases mounted to the plywood. I was planning to mount the electronics box at the same time, but there are some changes on that front. More on that later. #Maker

A piece of light brown plywood with some additional blocks of wood attached around the border. Three pairs of black nuts on top of silver washers can be seen protruding from the back of the board. Each pair runs horizontally, with the pairs arranged in a diagonal with respect to the rest of the box.

020

NessoAsks @nessoasks.bsky.social · 29/06/2026

I attached the first base to the plywood! The LumiDrive will connect to the grey & orange lever connectors at the bottom. I have a battery-powered book light illuminating the inside of the tower, which allows me to check the alignment with the front design. #Maker #FreeCad #3DPrinting

A white cylinder sits on a piece of light brown plywood. The cylinder has a piece of diffusion fil stretched across the top, which obscures the small book light I have inside.

At the bottom of the frame are four grey and orange lever connectors. One side of the levers connect to wires (not visible) that come out of the tower. The other side are open, and will connect to wires that come off of the LumiDrive processor that will drive the light sequence.

On the left side of the picture there is a black USB cable laying on the plywood.

051

NessoAsks @nessoasks.bsky.social · 26/06/2026

I was trying to build an adapter that would convert surface-solder pads into through-hole points. The grey 3D-printed piece bolted onto the LED ring would hold the wires in place. The larger piece this is a part of is a surprise!

110

NessoAsks @nessoasks.bsky.social · 26/06/2026

When you're testing a new electrical contraption and you smell smoke... that's bad, right? My side-quest to build an adapter to convert surface-mount solder points into through-hole points was not successful at this time. Back to surface-soldering! #Maker

A dark grey, non-static mat lays on top of a light brown work bench. There is a white partial-box with a red Lumidrive micro-processor inside on the mat in the foreground. It's connected via a series of colored alligator wires to a 2-inch diameter LED ring in the background, also on the mat.

In the extreme background is another light brown work bench with an assortment of other tools.

110

NessoAsks @nessoasks.bsky.social · 24/06/2026

I designed the adapter to be a low-enough profile that it would fit below the ring while it was mounted to the white base. I forgot, however, to build in clearance for the base's mounting holes. I'll need to carve out a few millimeters of room for them. #Maker #FreeCad #3DPrinting

A white, 3D-printed base sits on a dark grey work surface. The base is 10cm in diameter and 3mm thick. A 2-inch diameter LED ring sits on top of the base. Between the ring and the base is a light grey, 3D-printed adapter that clamps 6 wires to the surface mount pads on the underside of the ring.

There are 6 wires coming off the ring going to the lower left of the frame - 2 green, 2 blue, a white, and a red.

120

NessoAsks @nessoasks.bsky.social · 22/06/2026

Trying out the Prototype 9 adapter. The screws serve to both clamp the adapter and the wires to the LED ring, and to keep everything lined up. #Maker #FreeCad #3DPrinting

A 2-inch diameter LED ring sits on a dark grey work surface. Below the ring is a light grey, 3D-printed adapter that clamps 6 wires to the surface mount pads on the underside of the ring.

There are 6 wires coming off the ring going to the lower left of the frame - 2 green, 2 blue, a white, and a red.

030

NessoAsks @nessoasks.bsky.social · 19/06/2026

Me: Are you sure you're not trying to commit insurance fraud, Nutmeg? Nutmeg: Of course not, hoo-man. I'm comfortable here. Me being a tripping hazard sounds like a "you" problem. #Bunny #Bunnies #Rabbit #Rabbits

A view of a living room with a recliner on the left, a white cabinet, and a series of wire-mesh gates that bisect the room, keeping our two bunnies separate. A black bunny is sprawled on the floor in the center of the shot.

030

NessoAsks @nessoasks.bsky.social · 19/06/2026

If you don't see any differences between prototypes 3-8, don't worry. I was adjusting the placements of the holes by millimeters (and sometimes less). Now we'll see if prototype 9 can clamp the wires onto the LED ring. #Maker #FreeCad #3DPrinting

On a dark grey work surface lay 9 light grey, 3D-printed clamping prototypes lined up going left to right. Each one is numbered.

The first is a square 20mm on a side and 3mm thick.

The second is a half-circle that is roughly 45mm in diameter with a small "handle" sticking off the left side.

Prototypes 3-8 are slightly more than a half-circle and are only 1mm thick.

Prototype 9 is slightly more than a half-circle, is 3mm thick, and has the handle sticking off the left side.

Prototypes 2-9 have three holes (top, left and bottom) to attach to the LED ring.

000

NessoAsks @nessoasks.bsky.social · 17/06/2026

Side Quest: Can I build a bracket that allows me to attach wires to the LED ring without going through the process of surface mounting? Can I prevent ruining the pad when I brush past one of the surface-mounted wires? Asking for a friend. #Maker #FreeCad #3DPrinting

My first bracket prototype sits on a dark grey work surface (crisscrossed with scratches). The bracket is a square piece of 3D-printed plastic, 20mm on a side and 3mm thick, with four grooves on the top that run the full width of the piece.

In each groove is a wire. The bare copper has been pressed into the groove, holding it in place (barely). From top to bottom, the wires are colored white, green, red, and blue.

010

Reposted by NessoAsks

Abilu Tangwa. @abilutangwa.bsky.social · 16/06/2026

10 Reasons to Love Solar Power 1. Zero CO₂ to run 2.Infinite fuel 3.sunlight 4Cuts air pollution 5.Creates local jobs 6.Low water use 7.Price keeps dropping 8.Powers homes + grids 9. Works off-grid too 10. Energy independence Future-proof tech

497123373176

NessoAsks @nessoasks.bsky.social · 15/06/2026

I got the side cut off to allow the USB cables to enter (slot in the foreground), and got the electronics mounted. The M3 screws I'm using were too big to fit the holes on the USB power source (blue piece in front), so I could only add them to the red LumiDrive. Grr. #Maker #FreeCad #3DPrinting

A white 3d-printed box sits on a dark grey work surface.

The box has no top, only the floor and the sides. It has two sections of the walls cut out - one in the background to allow four wires to exit, and one in the foreground to allow for the USB power cables to enter.

Inside the box are two printed circuit boards - a small USB power converter sits in the foreground, and a larger red LumiDrive sits in the background. The two boards are connected by red and white wires.

In the background, poking out of the board, are four wires (white, green, blue, and red) that will lead to the LEDs.

051

NessoAsks @nessoasks.bsky.social · 12/06/2026

I 3D-printed a custom box for the electronics. The four risers with the heat-set inserts are the mounting points for everything. Of course I realized after the fact that I didn't leave a hole for the power cable to plug in. *facepalm* I'll fix that in post. With a saw. #Maker #FreeCad #3DPrinting

A white rectangular box sits on a dark grey work surface. The box has a portion of the wall removed from the upper right corner to allow for the wires that will lead to the LED lights.

There are four risers at the bottom of the box at various points. Each riser is 6mm tall with a 5.5mm outer radius. Mounted in each riser is a brass heat-set insert, threaded for a M3 screw.

There are also 3 small holes in the bottom of the box. These are what I will use to mount the box to the bottom of the piece I'm working on.

050

NessoAsks @nessoasks.bsky.social · 10/06/2026

I got all of the diffusion channels cut. Each one is fit to a specific strip of LEDs. The LEDs will slide into the base of the channel so that the light will be scattered through the top. Now I gotta cut all the wires - 4 for each junction between strips. Sigh. #Maker

On a dark grey work surface, there are 10 LED strips of varying lengths, some vertical and some horizontal. Next to each LED strip is a similar length of white diffusion channel.

000

NessoAsks @nessoasks.bsky.social · 09/06/2026

Bunnies are machines that turn hay into chaos. #Bunny #Bunnies #Rabbit #Rabbits

A near-floor level picture of a white rabbit with red eyes, black ears, and a black nose. The rabbit is to the right of the picture, eating out of a red and white ceramic bowl.

To the left of the shot and further into the background is a grey litter box. Litter has been kicked out by the rabbit onto the rugs on the floor. There are also several small toys, and several small black poops scattered around on the floor.

080

NessoAsks @nessoasks.bsky.social · 08/06/2026

I cut these sections of LED strip weeks ago, but this weekend I got all of the connections prepped for soldering. #Maker

A dark grey work surface with many scratches on it lies on a light brown workbench. On the work surface are 10 pieces of LED strips, ranging in sides from 2 LEDs to 12 LEDs. The 4 connection points on each end of each strip now have a small bead of solder.

000