iiinova — where your digital self keeps evolving

Dr H @drh.dice.camp.ap.brid.gy · 17/10/2026

Whatever chemicals are handled at this refinery, the signs are that they are not good for the health. And yet, someone has sneaked in and left their mark. #Scratchbuilt #TabletopTerrain #Refinery #DrH

Low angle view of the front of the refinery, a prominent sign declares "Biohazard".

Around the back of the refinery a plain structure with pipes leading in also carries a warning sign.

A hidden side of the same structure a small piece of graffiti says "Dr H woz ere"

002 2

Dr H @drh.dice.camp.ap.brid.gy · 10/10/2026

The tiles on the roof of the workshop are individually placed card hexagons. Naturally, I left some gaps and filled them with weeds. The digital screen sign for the shop has a few artifacts I painted on to try and illustrate that it's a screen and not just a sign […] [Original post on dice.camp]

Top down view of the infinity workshop roof.

Various close-ups showing the shop's sign "Mik's Mech Shop", a view of inside, and one side of the main door with some lights and digital displays.

Left side windows of the Infinity workshop terrain piece.

Right side windows of the Infinity workshop terrain piece.

020 2

Dr H @drh.dice.camp.ap.brid.gy · 09/10/2026

Plague Marine #4 In addition to a few tentacles, I also sculpted the plasma flame. #DeathGuard #Nurgle #PlagueMarines #DrH #Warhammer40k #WarhammerCommunity

All round angles of this Plague marine miniature.

041 4

Dr H @drh.dice.camp.ap.brid.gy · 03/10/2026

The last few photos of the broken bell tower. Ground floor; the fallen bell sits atop a pile of rubble. And the first steps on the tower's climb are lit by a still connected light. Painting the inside of the tower so dark allowed me to create this well-lit corner […] [Original post on dice.camp]

Moody-lighting photo of the inside of the broken bell tower.

Closer view of the ground floor of the broken bell tower to show the painted lighting of the "working" light.

010 1

Dr H @drh.dice.camp.ap.brid.gy · 30/09/2026

More angles of the Dredge boat diorama. The water was formed from shapes of polystyrene foam covered with tissue/PVA. This was filled, smoothed and sculpted with plaster. That was then painted in blues. Some areas were then filled in with clear(ish) hot glue […] [Original post on dice.camp]

Front view of the Dredge boat diorama. Low angle.

Left side view of the Dredge boat diorama. medium angle.

Rear view of the Dredge boat diorama. High angle.

Right side view of the Dredge boat diorama. Close up of the water and row of "teeth".

012 2

Dr H @drh.dice.camp.ap.brid.gy · 27/09/2026

Step into the darkness and seek the light ahead. #SilentSunday

A path extends into the shade of an archway of trees.

000 0

Dr H @drh.dice.camp.ap.brid.gy · 25/09/2026

The final few photos of the cartoon concept tractor. Close up shots show what can be seen of the model engine I installed. #Scratchbuilt #Concept #CartoonConceptTractor #Tractor #DrH

Rear view of the tractor model to really show the exaggerated wheels.

010 1

Dr H @drh.dice.camp.ap.brid.gy · 24/09/2026

The statue held a flag for Cadia, likely honouring the regiment for whom the statue was built. Even fallen, broken, decapitated, the statue continues to hold the flag. Cadia, and the Imperial guard, will live on. I made the flag detachable for storage/transport […] [Original post on dice.camp]

Close-up of the flag held by the fallen statue.

The torso of the fallen statue, holding the flag still.

000 0

Dr H @drh.dice.camp.ap.brid.gy · 23/09/2026

And a scale shot of the Ankylosaurus Prime and their brainwashed Tyranid warrior siblings. #MiniaturePainting #WarhammerCommunity #Warhammer40k #Ankylosaurus #AnkyPrime #DrH

Scale photo of the Ankylosaurus Prime miniature conversion to three Tyranid warrior miniatures.

0102 10

Dr H @drh.dice.camp.ap.brid.gy · 22/09/2026

The fourth pair of Pox walkers. Vanilla on the left, Conversion on the right. For the arm swaps of this conversion I went really asymmetrical; Large weapon arm, and a small deformed arm that they use to huff whatever is in that tank. There's a few more changes […] [Original post on dice.camp]

010 1

Dr H @drh.dice.camp.ap.brid.gy · 19/09/2026

And the third leg, around the rear of the Foetid Bloat Drone tripod. To keep with the insect-vibe of the model, the rear leg became more of a spike (like a tail sting) rather than another leg to match the first 2. Extending from the rear of the drone's body […] [Original post on dice.camp]

Rear views of the Foetid Bloat Drone tripod conversion.

011 1

Dr H @drh.dice.camp.ap.brid.gy · 08/09/2026

And one last look at the Chaos Dreadnought (Helbrute), with all the scratch-built and magnetised weapon options. #ChaosDreadnought #Helbrute #Warhammer40k #WarhammerCommunity #DarkVengeance #DrH

Modified chaos dreadnought / Helbrute miniature. Surrounded by it's weapon options:
Left of Helbrute (Left to right);
Twin-linked Las Cannon,
Plasma Cannon (front),
Reaper Auto-cannon (back),
Multi-Melta (back),
Heavy Bolter (middle),
Power Fist with options (l-r) Heavy flamer, Combi-bolter, Chaos star plate.

Right of Helbrute (right to left);
Power Scourge (back),
Chaos star armour plate (back),
Power fist (back),
Thunder hammer (front),
Plain armour plate for attachments (middle),
Combi-bolter attachment (middle),
Heavy Flamer attachment (middle),
Optics attachment for missile launcher (middle),
Missile launcher (front).

010 1

Dr H @drh.dice.camp.ap.brid.gy · 08/09/2026

And now the pair of them primed and ready for painting... when I decide what colours I'm going to paint them... The bases, as shown, are up to the basic level of mud and rocks. There'll be some plants of some kind added at the end. The lightning arcs of the drone […] [Original post on dice.camp]

Tau stealth suit miniature. Primed and on it's base.

Tau shield drone miniature conversion. Primed.

000 0

Dr H @drh.dice.camp.ap.brid.gy · 06/09/2026

I've mentioned it before, but I don't think I've ever shown you lot here, how I base my mini's. The main difference is the mixture I use for the texture. My mud'n'rocks mix is mostly crumbs of dried paint, plaster, shavings and sawdust of wood and plastic, and […] [Original post on dice.camp]

Various photos of a miniature's base during the stages of production.

Top:
Left; Glued base sprinkled with my mud'n'rocks mixture.
Often coated with watered-down PVA afterwards to ensure everything's stuck.
Middle; Painted brown.
Right: Wash with black to darken recesses.

Bottom:
Left; Dry-brushed with a mid-brown and then a light brown.
Middle; Anything that looks like a rock is painted dark grey then dry-brushed light grey.
Right; The whole base is dry-brushed with on off-white and then with white to pick out the sharpest points/edges.

Afterwards, I can add more details, plants, static-grass, etc.
Larger things are usually added before paint.
The miniature is usually added afterwards, especially if it would get in the way of painting.
Anything that gets in the way of adding the mini' can easily be removed.

Sometimes I'll position the mini' while the glue is drying after sprinkling, to make space for the feet.
And only on certain occasions will I actually glue the mini' on at the first step.
And sometimes the base will be painted at the same time as the mini', but with all that dry-brushing it's easier if the mini' isn't in the way.

021 2

Dr H @drh.dice.camp.ap.brid.gy · 04/09/2026

A bonus wip. On the same sprue was a Tau drone, so I thought I'd make one of them as well. Many of the bits I pulled out for the Stealth suit, but didn't use, I stuck on to this. More details in the alt text... Then in continuing with my opposition to clear […] [Original post on dice.camp]

Various angles of a modified Tau drone.

Due to the Eldar waveserpent shield spine thing, I decided that this is a shield drone.
Therefore, no weapons but lots of gubbins. And a megaphone to distract enemies as part of an invulnerability save.

120 2

Dr H @drh.dice.camp.ap.brid.gy · 02/09/2026

Where we are "now now" with the stealth suit. I added some triangles of clear ABS to break up the square-ness of the arm area. I see these shapes as shifting through each other as the suit cloaks/uncloaks. From a distance it does actually look like a detailed […] [Original post on dice.camp]

Various angles of the stealth suit miniature in progress.

111 1

Dr H @drh.dice.camp.ap.brid.gy · 01/09/2026

The stealth suit now has an "invisible" arm on. Meant to share this earlier, so you'll likely get another wip tomorrow. #WIP #Stealthsuit #DrH

Various angles of the stealth suit mini' in progress.

121 2

Dr H @drh.dice.camp.ap.brid.gy · 01/09/2026

Something clearly went wrong inside the Chemist's Den. A storage/mixing tank has ruptured and taken part of the hut's wall with it. It gives you a good view inside the hut. Or lets light in so you can see through the open door (if it's open). #ScaleModel […] [Original post on dice.camp]

The broken side of a wooden hut, a ruptured tank is visible inside.

A look along the length of the underside of the roof.

022 2

Dr H @drh.dice.camp.ap.brid.gy · 28/08/2026

Closer views of the pallets I made to go with the near-future forklift. The pallets are mostly card, as are the cardboard boxes. Plus some small cotton reels on one, and plastic tube for the barrels. Made to fit the fork of the forklift, of course. #ScratchBuilt […] [Original post on dice.camp]

More angles of the pallets, including the underside.

021 2

Dr H @drh.dice.camp.ap.brid.gy · 28/08/2026

One more wip for the week. With the success of the leg we move on with this method. Next, carefully cut off the shoulder (can use it later for something) and glue on a piece of plasticard to make it flat for attachment of the block of acrylic you have cut to size […] [Original post on dice.camp]

Work in progress photos of the stealth suit.
Top, remove shoulder and replace with plasticard and acrylic.
Middle/bottom; various angles of the leg attached.

111 1

Dr H @drh.dice.camp.ap.brid.gy · 26/08/2026

Scythe boardgame figures from the Polania Republic faction. Including Anna and Wojtek the bear. And with a set of white Mechs. #ScytheTheGame #Scythe #Saxony #boardgames #MiniaturePainting #DrH

Polania Republic figures from the Scythe boardgame.

Anna & Wojtek figure, front and bear side view.

063 6

Dr H @drh.dice.camp.ap.brid.gy · 26/08/2026

Experimental update for the cloaked elements of the Stealth suit: Working with pieces of clear styrene and acrylic. Gluing; Liquid cement - not good. Leads to clouding long after application. High risk of getting it where you don't want. Thick cement - works for […] [Original post on dice.camp]

Work in progress experiments with constructing in clear plastic. First few elements of leg replacement glued with superglue, next to the removed leg.

120 2

Dr H @drh.dice.camp.ap.brid.gy · 22/08/2026

Side-on views of the Luggage Mimic. The metalwork is made from plasticard with a little epoxy putty for gaps. The rivets are water-filter beads glued into drilled dips. #TheLuggage #Discworld #Mimic #Scratchbuilt #DrH

Right side of the Luggage Mimic model. Lid closed.

Right side of the Luggage Mimic model. Lid open.

Left side of the Luggage Mimic model. Lid closed.

Left side of the Luggage Mimic model. Lid open.

011 1

Dr H @drh.dice.camp.ap.brid.gy · 21/08/2026

What's this? A project idea from long ago; A stealth suit partially cloaked... To start with, collect pieces to build and add some other bits to incorporate. Because I can't just build a mini', I have to modify it to fit my army/collection. Glue some bits […] [Original post on dice.camp]

Top left; collection of pieces for the miniature. Pull out more than I need and see what fits.

Top right: Glue together the body and then cut off the jet-pack. Build a replacement, but a Necron gun part is too long so cut out the middle and glue those together (bending the "cable" to fit).

Bottom left: New back pack is a Las-cannon battery, Necron gun part, an old space marine backpack vent and a deathmark's teleport orb.
This chap won't be jet-packing about, he'll teleport.
Shown with arm in position but not glued.

Bottom right: Leg attached. Why "leg" and not "legs"? of course I've cut one off so that it can be the "cloaked half" either merged with terrain or made from transparent parts. That's why there's also no left arm.

111 1

Dr H @drh.dice.camp.ap.brid.gy · 21/07/2026

Final set of photos of the flying Kroot. The base is fairly simple, being small, but the leaves are a twist-tie sandwiched between craft tissue with plenty of PVA. Cut to shape these can then be "posed" however you like due to the wire. One leaf hides a thicker […] [Original post on dice.camp]

Rear view, high angle, of the flying Kroot.

Left rear view, high angle, of the flying Kroot.

000 0

Dr H @drh.dice.camp.ap.brid.gy · 18/07/2026

More photos of the Cyberdeck prop. A press of one of the buttons lights up 3 LEDs about the 'deck. And one of the plugs on top can be pulled out and retracts as if elastic. The various other buttons don't do more than click, and there's a sprung-loaded […] [Original post on dice.camp]

Various angles of the cyberdeck prop. Showing the press of a button leading to lights, and one of the plugs being pulled out on a cable.

030 3

Dr H @drh.dice.camp.ap.brid.gy · 15/07/2026

More extreme angles of the Deino-bot. I gave the model a short tail for convenience, but made it look weighted so that it can still act as a counterbalance for the body. #DinoBot #Deinobot #Scratchbuilt #Dinosaur #Deinonychus #HorizonZeroDawn #DrH

Right side, from above, of the dino-bot model.

Right side, from below, of the dino-bot model.

010 1

Dr H @drh.dice.camp.ap.brid.gy · 13/07/2026

A few more views of the UFO abduction diorama. I saw a UFO once, but then the plane changed direction and I could tell it was the landing lights that had been pointing right at me. #UFO #UFOAbduction #ScaleModel #Cow #DrH

UFO abducting a cow diorama. Low light to show the tractor beam light.

UFO abducting a cow diorama. With red cabin lights on.

UFO abducting a cow diorama. Red lights on.

041 4

Dr H @drh.dice.camp.ap.brid.gy · 11/07/2026

Cyberdeck prop, original design model. Inspired by Cyberpunk 2077 and the like. Made from a collection of junk pieces. Gave me a chance to raid my boxes of electronic junk for switches, lights and circuit-boards. I designed it to look like it can be folded in […] [Original post on dice.camp]

171 7

Dr H @drh.dice.camp.ap.brid.gy · 09/07/2026

A final look at the Thorin Oakenshield / Goblin King diorama. This time from the POV of each of them. Each pair of photos shifts the focus from the near to the far character. #LotR #TheHobbit #ThorinOakenshield #GoblinKing #GoblinVsDwarf #Diorama #DrH

View from the right side of Thorin Oakenshield towards the Goblin King.

View from the left side of Thorin Oakenshield towards the Goblin King.

View from the right side of the Goblin King towards Thorin Oakenshield.

View from the left side of the Goblin King towards Thorin Oakenshield.

000 0

Dr H @drh.dice.camp.ap.brid.gy · 03/07/2026

More angles of the Raider gunship. I couldn't resist using a pair of eyes on the nose; transfers from an A-10 model. #DarkEldar #RaiderGunship #Warhammer40k #Conversion #WarhammerCommunity #DrH

Front-on view of the Raider gunship model.

Rear view of the Raider gunship model. high angle.

Front left view of the Raider gunship model.

Rear right view of the Raider gunship model. high angle.

031 3

Dr H @drh.dice.camp.ap.brid.gy · 27/06/2026

More views of the inside of the Predator tank. Before doing much of the outside of the tank I built and painted the interior. This Includes the interior workings of the sponsons (as well as the outside of them), The aforementioned driver and his seat etc., The […] [Original post on dice.camp]

Interior of the modified Predator tank, Right and rear. Before sealing up the structure to build the outside.

Interior of the modified Predator tank, Left and roof.

100 1

Dr H @drh.dice.camp.ap.brid.gy · 26/06/2026

Inside the N-gauge train shed. I left the pile of "goods" ready to be loaded, and a sign that my Granddad had added. I assume the sign was not part of the kit, as why would a train shed have a large sign for "plastic models" on the inside. Also a photo of the […] [Original post on dice.camp]

View through the side door of the train shed, showing a sign that reads "plastic models".

View along the tracks from one end of the train shed.

The disassembled model before repairs and repainting.

010 1

Dr H @drh.dice.camp.ap.brid.gy · 25/06/2026

I also installed a LED at the back of the Mirkwood Book Nook. So there is a mysterious light deeper into the wood, it's probably elves... probably. #LoTR #Mirkwood #BookNook #Scratchbuilt #DrH

Low-light photos of the Mirkwood book nook to show the light in the depths of the nook.

000 0

Dr H @drh.dice.camp.ap.brid.gy · 24/06/2026

Around the back of the "Refinery?" a small mass of cables and pipes join the main building to the external grey block. Like most of the build it was an exercise in making it look complicated, but realistic. #Scratchbuilt #TabletopTerrain #Refinery #DrH

Rear view of the Refinery terrain piece.

Close up of some cables and pipes joining to the main building.

Close up of the mass of supported cables and pipes.

High angle, close up of the mass of supported cables and pipes.

100 1

Dr H @drh.dice.camp.ap.brid.gy · 23/06/2026

One last look at Ol' One Toof, as the Ork Nob charges towards you. Are you still laughing at the funny greenskins? #Warhammer40k #WarhammerCommunity #Ork #OrkNob #DrH

POV shot of an Ork nob miniature as they charge towards you.

000 0

Dr H @drh.dice.camp.ap.brid.gy · 18/06/2026

And some closer views of the squad leader of the Rescue Terminators. Storm bolter and power-sword. I painted the sword in metallics, and then added the lightning bolts for the "power" effect. #Warhammer40k #WarhammerCommunity #TerminatorSquad #BloodAngels #RescueTerminators #DrH

Blood angels Terminator space marine miniature.

011 1

Dr H @drh.dice.camp.ap.brid.gy · 16/06/2026

I made a few scatter terrain pieces to go with the workshop. A set of crates, using my box kits, and a couple of pallets with various cardboard boxes. All with cloth/tarp covers. I painted the inside/outside of the cloth different colours so that it's obvious how […] [Original post on dice.camp]

Side view of the roof of the infinity workshop terrain. With scatter terrain pieces and infinity miniature for scale.

Roof of the infinity workshop terrain with scatter terrain pieces and infinity miniature for scale.

Side views of the scatter terrain pieces.

Front and back views of the scatter terrain pieces.

140 4

Dr H @drh.dice.camp.ap.brid.gy · 12/06/2026

Plague Marine #3 Aside from the usual re-posing and fixing casting limitations, this chap got a purple tentacle readying a plague grenade. #DeathGuard #Nurgle #PlagueMarines #DrH #Warhammer40k #WarhammerCommunity

Plague marine miniature. All-round angles.

161 6

Dr H @drh.dice.camp.ap.brid.gy · 08/06/2026

The middle floor of the Broken Bell Tower. A ladder reaches up from below, and the start of a staircase is all that remains after the wall fell away and the bell passed through. Some rubble and a discarded drinks can lay on what remains of the floor. Plus some […] [Original post on dice.camp]

High angle photo of the middle floor of the broken bell tower.

Low angle, close-up photo of the middle floor of the broken bell tower.

High angle photo of the middle floor of the broken bell tower. Lit only by light through the window slit.

Photo of the middle floor of the broken bell tower. Lit from the other window slit.

130 3

Dr H @drh.dice.camp.ap.brid.gy · 07/06/2026

@kirasha All are good options; Karlach and Gale both have some nice variations to the story, 2nd only to Shadowheart and D'urge. I did do a run specifically to make all the choices that I didn't usually do (to not upset people). I saw her more as an awkward teen […] [Original post on dice.camp]

Baldur's Gate screenshot of a party of adventurer, plus a lot of summons.

100 1

Dr H @drh.dice.camp.ap.brid.gy · 06/06/2026

The last couple of angles of the N-gauge train display base. I used foam to make some bushes under the platform, there's also some spare sleepers under there. The length of track is part of a bent and broken piece, repaired for this purpose. The ballast is […] [Original post on dice.camp]

Front left view of the N-gauge display base. No train.

Front left view of the N-gauge display base. With train.

Overhead view of the N-gauge display base. No train.

Overhead view of the N-gauge display base. With train.

010 1

Dr H @drh.dice.camp.ap.brid.gy · 03/06/2026

More from the Dredge boat diorama. The boat started as a cardboard skeleton that I then skinned with plastic. I then cut off the bottom half when I realised that it's going to be immersed in water. The upper parts are mostly plastic and epoxy putty. #Dredge […] [Original post on dice.camp]

Front right of the boat diorama. Low angle.

Rear right of the boat diorama. High angle.

Close up of the left side of the water and teeth.

Left side of the boat diorama from above.

130 3

Dr H @drh.dice.camp.ap.brid.gy · 01/06/2026

And finally the wall-breaking Inceptor. Made to look as if he's just kicking his foot into a brick wall to get a leg up. A brick wall is no more substantial than a pile of plastic foam. Incidentally, this wall was made from "bricks" of foamcore with some plaster […] [Original post on dice.camp]

Front and side view of the wall-breaking Inceptor space marine.

Side and rear view of the wall-breaking Inceptor space marine.

High angle and rear views of the wall-breaking Inceptor space marine.

Side views of the wall-breaking Inceptor space marine.

041 4

Dr H @drh.dice.camp.ap.brid.gy · 30/05/2026

Dredge boat diorama. Based on the basic boat from Dredge. I don't know much about the game really, I've only played the first few days. I was also a good boy and returned to port before dark. But I get the impression that something like this could happen […] [Original post on dice.camp]

Right side, low angle, of the boat diorama. The boat float peacefully amongst the waves of the ocean.

Rear left, high angle, of the boat diorama. "I've hooked something", "Reel it in then".

Front view from above, of the boat diorama. Why is the water rising and what are those things breaking the water around the boat?

Front view of the boat diorama. Close up of the water on the front edge showing the rise of this patch of water and it spilling out from the gap between the 2 halves of the mouth.

142 4

Dr H @drh.dice.camp.ap.brid.gy · 29/05/2026

Some more of the cartoon concept tractor model. Painting was obviously based on a John Deere tractor, and the windows are painted as if reflecting the surrounding field and clear blue sky. #Scratchbuilt #Concept #CartoonConceptTractor #Tractor #DrH

Front right of the concept tractor model. High angle.

Left rear of the concept tractor model. High angle.

Rear right of the concept tractor model. Low angle.

110 1

Dr H @drh.dice.camp.ap.brid.gy · 28/05/2026

A closer look at the plinth itself of this fallen statue. The statue's feet remain atop, the legs breaking for some reason in the past. Posters and items of tribute surround the plinth. But where a dedication should be written, someone has obscured what was […] [Original post on dice.camp]

On the "path" side, nearest the fallen statue, a poster warns of "Aliens". It is damaged by incoming fire, much like the rest of the plinth and barricade.

The front of the plinth has been defaced with a Chaos emblem.

An motivational poster for "Cadia" is on the side nearest the shrine.

And on the outside a bolter hangs from a hook and at the base a knife and grenades have been left in tribute

111 1

Dr H @drh.dice.camp.ap.brid.gy · 27/05/2026

Closer views of the weapon arms of the Ankylosaurus Prime. The right arm(s) combine a Tyranid barbed strangler with a space marine heavy bolter (from a Predator tank), and an underslung Eldar missile launcher. And for close quarters, one of the left arms has a […] [Original post on dice.camp]

Various angles and close-ups of the Ankylosaurus prime's weapons/arms.

2142 14