iiinova — where your digital self keeps evolving

Andrey @spirit.re · 10/08/2026

Sneak peek of a small side project: The world's highest resolution, highest frame rate thermal imaging phone-attach camera: 640x512 at 60Hz(!), in a tiny 25x25x38mm package. Radiometric w/ recording, focuses from ~8mm macro to infinity. Works on Android&iOS + Windows/MacOS/Linux.

Render of a 640x512 thermal imaging phone dongle

Real photographs of the 640x512 phone dongle prototype. No label engraving. Real lens visible.

A superresolution capture(real thermal data, higher than 640x512 native pixel size) from the camera prototype, produced in-software, then upscaled another 2x for pleasant viewing.

040

Andrey @spirit.re · 29/07/2026

During the process of cleaning a capillary used to feed and bond the wire onto the chips, I had a small intrusive thought... and it may have won...

010

Andrey @spirit.re · 28/07/2026

I'm working on retrofitting a wire bonder with custom electronics as part of a small side project(yes, to also make them cheaper). I think it's neat how the electric flame-off(EFO) gold ball forming system works when viewed at high magnification. Here's a short video about it.

010

Andrey @spirit.re · 01/07/2026

A little sneak peek of another project I'm working on. Can you guess what this is? :)

An uncommon object that involves ruby, sapphire, stainless steel and gold.

000

Andrey @spirit.re · 29/06/2026

I got one of my high speed cameras to try filming an ozone generator's dielectric barrier discharge, but the camera wasn't sensitive enough. Can't put a high speed camera away without filming something, them's the rules, so have a can of brake cleaner spraying at 895fps instead.

130

Andrey @spirit.re · 06/05/2026

Decided to try a little experiment - zooming in from 15x to 100,000x in smooth progression. The SEM isn't particularly well calibrated so the result is only ~30-40nm resolution, but I think it's still pretty neat. Working on making SEMs so affordable you could have one at home :) 🧪 HQ link in reply.

110

Andrey @spirit.re · 12/04/2026

Tungsten & oxides deposit on the Wehnelt and anode of SEMs as filament evaporate and gunk in the chamber hits it. Abrasives are used, but I found an alternative: 1:1 solution of 10% ammonia to 3% H2O2! If aluminium is present, oxides grow and a 5% phosphoric wash is needed after. 🧪

A heavy oxide and tungsten metal film is visible deposited in a rainbow pattern on the filament side of the wehnelt cup of an electron microscope.

The same Wehnelt cup, after cleaning with a 50:50 mix of 10% ammonia and 3% hydrogen peroxide solution, as well as a 5% phosphoric acid rinse due to the presence of aluminium.

020

Andrey @spirit.re · 24/02/2026

Tinkering with electron optics simulation this evening, came up with a little test software for boundary element method simulation and particle tracing. So far so good, and I think it has potential as an educational & low-complexity pro design tool. Would you want to use this? 🧪

Screenshot of a work-in-progress charged particle optics simulation software, showing traces of electrons being emitted from a narrow bar's surface, traveling between and being deflected by two charged squares, accelerating into a cylinder at high potential.

030

Andrey @spirit.re · 05/01/2026

Neat paper I missed in 2024 - these guys took an ultrasonic wedge wire bonder - the kind that's used to attach wires to chips - scaled it up by 15x, and used it to 3D print aluminium! Pretty cheap to implement, not much to it. Pretty cool. Open access, DOI: 10.3390/ma17102188 🧪

020

Andrey @spirit.re · 15/11/2025

One of the more unusual workplaces for an engineer to be. Plugging something you designed and built into an obsolete avionics system that would cost more than your entire net worth to replace is... one of the feelings of all time, for sure. The jet is a Cessna Citation Bravo.

An overview of the cockpit of a Cessna Citation Bravo in the middle of an overhaul, with a custom diagnostics instrument attached to the avionics.

020

Andrey @spirit.re · 04/11/2025

Built a small optical coordinate measurement machine and wrote a basic but mostly feature-complete software for it. Telecentric optics, so no perspective error. Resolution ended up at ~4µm for this ~30mm FOV. Would you want a nicer version of this(housing, lights) for ~2.5k? 🧪

An optical CMM based on a telecentric lens and a high resolution camera, mounted on a large and high precision vertical translation stage. Flat backlight visible below.

General macro overview of the scene being measured by the CMM. 0.5mm pitch connector, M3 screw, glass calibration scale.

Screenshot of the user interface with feature recognition enabled and a few measurements added.

Second screenshot of the user interface, measuring thread parameters.

120

Andrey @spirit.re · 13/10/2025

Sipeed sent me their new SLogic16U3 USB3 logic analyzer to review(free, no obligation). Inside is just a tiny Gowin GW5AT-LV15 FPGA doing softcore USB3(!!!), which is how they made it so cheap. 800MHz@4ch is quite impressive. My verdict? Definitely going in the tool box. 🧪

Inside the logic analyzer. Gowin GW5AT-LV15 FPGA.

Underside. Power supply and miscellaneous.

Sigrok PulseView software showing 800MHz sample rate on 4 channels.

130

Andrey @spirit.re · 29/09/2025

Have you ever wanted to see a 90 second abridged explanation of how diode lasers work? Here it is. I took some pictures of a laser under my SEM, and it kind of just scope crept into a whole video. Not perfectly accurate, but it's hard to squeeze 100 books of info into 90 seconds.

031

Andrey @spirit.re · 13/09/2025

Ever wondered how infrared thermometers work? By connecting over 100 thermocouples in series, all on a MEMS chip, floating in a vacuum! The cold side is connected to the base, thermal radiation is focused onto the hot side, and the Seebeck effect gives us a proportional voltage. 🧪

This image shows an infrared thermometer, also known as a pyrometer. Inside is a small hermetically packaged metal can containing a thermopile. There are two images showing the thermopile as a general overview and up close. A reference thermistor that measures the base temperature is visible on top.

Two scanning electron microscope images of the device, much closer in magnification. Top shows the positive and negative wires, and the bottom shows the structure of multiple thermocouple junctions around an absorber.

Two scanning electron microscope images, showing a closeup of how the thermocouples are connected in series around the cold side, the substrate.

020

Andrey @spirit.re · 29/08/2025

First handheld laser welds, cuts, some cleaning. What the internet says is true this time - compared to regular welding(MMA/MIG), this is, no exaggeration, a point&click tool. 10 minute learning curve. Some nuances like penetration and fillet size, but overall just spectacular.

First handheld laser weld between 2.5mm thick square tube and 5mm thick plate. Both carbon steel.

Triple pass weld with the same settings to fill out the joint. Needs more filler wire or a slower run.

Aluminium tube cut freehand at 1.5kW power with a ~250µm wide kerf and near zero dross. Incredible maneuverability, like butter.

Closeup of the cut pieces, seen from the inside. In the background, a laser cleaned section of the plate, shiny finish.

010

Andrey @spirit.re · 21/08/2025

Design, reality. Looks pretty accurate :) High speed imaging will be affordable, and hopefully soon.

An image sensor test board, designed in KiCAD. 3D render.

The same board, but manufactured and assembled in real life.

140

Andrey @spirit.re · 06/08/2025

I've made a big step and finally touched an FPGA on a personal level. Fighting the development environment was 90% of the effort and only 10% was learning how this whole HDL/constraint thing works. Now to draw the rest of the owl. In my case, a high-speed camera shaped one.

040

Andrey @spirit.re · 02/08/2025

Who needs Boston Dynamics and Unitree when you can have Soviet Dynamics? This 45 YEAR OLD(!) film shows the exact thing techbros have been parading around for the past few years. LIDAR, SLAM, multi-core mainframes, live trajectory and path planning, IK, simulation, all from 1980 youtu.be/_klAzHoI7S0

youtu.be

WalkingMachinesNIITransmash1980

YouTube video by Spirit

010

Andrey @spirit.re · 31/07/2025

Did I *need* to create an extremely detailed 3D model of an image sensor, down to the bond wires, overlaid sensor structure and modeled pads, just to put it on a PCB design? No. But did I spend quality CAD time doing that and then rendering it out for fun? Absolutely.

Accurate, realistic 3D render of a high speed CMOS image sensor in its package. Bond wires, pads, and clear chip outlines are visible, as well as some of the PCB layout.

010

Andrey @spirit.re · 10/07/2025

Some incredibly cool pre-production silicon just showed up in the mail: >2K resolution at >600 frames per second, >10kfps with windowing, global shutter, HDR. This may be the first image sensor to make high speed cameras truly affordable for *everyone*.

010

Andrey @spirit.re · 04/07/2025

Do we have anyone with contacts at Xilinx/AMD? I want to get some samples of the new Spartan UltraScale+ chips. Specifically XCSU65P in CMVB529. And ideally a dev/evaluation board(SU65P or higher, need PCIe). My DMs are open, email works too - see my site.

010

Andrey @spirit.re · 24/06/2025

Got some 1.5kW and 2kW air cooled laser welder+cutter systems in to try a distribution model(EU & US). Very clean builds inside - DC PSU, nameless laser source, OEM control panel, minor gas handling. Simple, but affordable and effective. Also going to mod cleaning mode into it ;)

A 1500W air-cooled laser welder, hand next to it for scale. Wire feeder in the background.

Inside the 1500W air cooled laser welder. Power supply visible in front, big laser source in the back, small power supply below and control electronics above. Also some gas handling hiding behind the small power supply.

Inside the 2000W unit. Same thing, except bigger, and slightly more advanced gas handling. Notable is the Huawei cell tower equipment power supply.

010

Andrey @spirit.re · 18/06/2025

Helped with a bit of repairs on a Mooney M20M(Bravo) recently, then went up in it! General aviation is really fun, and if you ever get the chance to go flying, you should definitely say yes!

A Mooney M20M(Bravo) single-engine, 4 seat, low-wing airplane.

Inside the Mooney M20M in flight. Modernized glass cockpit.

View over the right wing while flying low over a city on a clear, mostly cloudless, hot day.

030

Andrey @spirit.re · 11/06/2025

Anyone out there with access to a research fab at reasonable rates? I want to test a relatively simple and potentially groundbreaking semiconductor device, but with a very exotic stackup. I need ALD, PECVD, and likely DRIE. Low res maskless litho is fine. Preferably in the EU.

020

Andrey @spirit.re · 18/05/2025

Is there any commercial interest in a desktop-ish full-cycle PCB "printer"? I proved out all the processes for fully automated, mostly chemical-free production of 2-layer PCBs with trace/space/via as small as 75μm. It could be relatively affordable, but not quite hobbyist-priced.

Complete single-layer PCB without silkscreen, made by a fully automated system.

A relatively large plated copper via made by a fully automated process.

270

Andrey @spirit.re · 26/04/2025

Ever wondered what TIG welding with neon gas would be like? No? Anyway, here's TIG welding with pure neon instead of argon. Video from Zerg Labs' archive.

010

Andrey @spirit.re · 03/04/2025

Got this very neat radiometric 640x512 thermal imaging core. Miniaturization is wonderful, it's just the WLVP image sensor directly wire bonded onto the board, with an ASIC on the back to crunch data. There are no affordable phone dongles with this resolution, so I'll make one.

Thermal image core with the lens and lens mount removed. The shutter assembly is visible in its retracted state, with the sensor visible through it.

The lens assembly on its own, showing the back element and design simplicity.

Back of the main thermal sensor board. An ASIC(supposedly) is visible in the middle, right below where the sensor is mounted on the other side. Some power supplies, flash memory, and other minor components.

110

Andrey @spirit.re · 12/03/2025

Silly computer peripheral idea: would you want an ultra-lightweight(world's lightest?), completely battery-free, permanently wireless 8kHz polling rate mouse, if it was confined to a special powered mousepad(~0.6mm thick, goes under your actual mousepad)?

120

Andrey @spirit.re · 18/02/2025

Is it safe to clean ball bearings in an ultrasonic cleaner? Turns out, it isn't! I investigate this with a scanning electron microscope in this video: www.youtube.com/watch?v=-g6g... 🧪

youtube.com

Does ultrasonic cleaning damage ball bearings? Electron microscope investigation!

YouTube video by Spirit

030

Andrey @spirit.re · 15/02/2025

Someone asked whether it's possible to build a DIY backscattered electron detector for a SEM. Yes, it's pretty easy! You just need bare PIN photodiodes, a trаnsimpedance amplifier, and a signal input. S=SED, R=BSED. Sample: rock section, ~nm of Au on top. Some charging visible.

A small collage showing the detector as-built, the photodiode, where it's installed, and a schematic for replication.

Secondary electron image. Some charging(full white spots) is visible due to the poor gold coating.

Backscattered electron image, better showing compositional contrast.

040

Andrey @spirit.re · 26/01/2025

Here's a soviet K573RF2 EPROM under the newly repaired SEM.

Soviet K573RF2 EPROM scanning electron microscope image

140

Andrey @spirit.re · 26/01/2025

Oops! All electron microscopes. I have another patient in the lab, this time it's a Keyence VE-7800 from the early 2000s. Let's dig in and take a look at the insides to bring it back to life! Lots of pictures in the thread.

Keyence VE-7800 scanning electron microscope, face on.

Keyence VE-7800 scanning electron microscope, view from the side. Extra ports are visible.

130

Andrey @spirit.re · 25/01/2025

Here's a reconstructed CT scan of a SEM filament. The disk on top is the Wehnelt... disk, I suppose, that serves to create the crossover pinch and adjust emission spot size. The four screws are used to center the filament within the cartridge.

050

Andrey @spirit.re · 24/01/2025

Loud vacuum pump, air compressor, or similar device that drives you crazy? Build a suspended vibration & noise isolation box! All you need is wood, rebonded sound absorbing foam(not cheap low-density sponge!), bungee, and fans. Sound levels drop by as much as 12dB! Video below.

Pump vibration and noise isolation box, lid open

Inside, showing a closeup of the floating platform

A drawing showing the dimensions and internal construction, to replicate for yourself

120

Andrey @spirit.re · 21/01/2025

If you use rotary vane vacuum pumps, here's a neat trick: you can use 0.1-0.5um polypropylene water sediment filter cartridges(not wound rope!) as dirt cheap oil mist eliminator filter replacements. Optionally some activated carbon around it, to stop any smells. Works great.

Ulvac OMT-200A oil mist trap. Original cartridge visible.

DIY replacement cartridge with activated carbon

000

Andrey @spirit.re · 15/12/2024

And, of course, being in FA-FO's lab, we had to test the Gardena High Vacuum System for performance. The results being good makes it just that much better.

000

Andrey @spirit.re · 15/12/2024

I didn't just get the helium leak detector to play around with, so let's put it to use. This whole repair ordeal happened in the FA-FO lab(fa-fo·de), where the goal was to test their JEOL JSM-T330A SEM. This video shows the same eyelash, and a massive travel time through the SEM!

000

Andrey @spirit.re · 15/12/2024

After very jankily connecting my new helium leak detector to the forepump using the world's most inconveniently sized bellows hose, I was presented with a very unhappy device - incorrect operation, max pressure shown. Which meant a teardown investigation was in order! (thread) 🧪

Leybold UL100 Plus helium leak detector being very unhappy and showing incorrect readings

Service panel of the UL100 Plus showing bad readings and a missing status indicator

110

Andrey @spirit.re · 15/12/2024

In my search of a suitable forepump, I managed to acquire this Ecotec 500. I didn't actually know what it was - it turned out that it's a sniffer-type gas analyzer for some kind of industrial process. But I got the pump that I really wanted out of it, and an RGA/turbo as a bonus! 🧪

Leybold Ecotec 500 sniffer thing, missing some parts.

Inside of the Ecotec 500. A residual gas analyzer, or RGA, is visible.

Sniffer capillary connection, vacuum gauge, and a turbomolecular pump peeking out at the back.

A Leybold D1.6B forepump, factory modified for extra functionality with additional valves.

000

Andrey @spirit.re · 15/12/2024

So I managed to acquire this Leybold UL100 Plus helium leak detector through a happy accident. It's old, made in the 2000s, but it was supposedly in good condition, just missing the forepump. Last service date shows 2021, and it has a 1993 test leak, refilled in 2021 as well.

Photo shows a Leybold UL100 Plus helium leak detector from the front. Black and white box with a control panel and KF25 test port.

The internal service control panel of the UL100 Plus, showing a diagram of its internal workings with status lights, some switches for manual control, and test points.

000

Andrey @spirit.re · 26/11/2024

Do I have any wine/linux experts following me? I think I want to throw out a small $ bounty for anyone who can get a particular piece of CAD software running under wine. 99% of it works, but the 1% makes it unusable - SVG icons don't render. Complicated problem. DMs open.

010

Andrey @spirit.re · 19/11/2024

You know, with how ambitious my current projects are, every time I interact with MCAD tools I get an overwhelming urge to put all of that on pause and start a brand new CAD/CAM/CAE company to completely upend that market by starting from scratch. Anyone have a few million spare?

010

Andrey @spirit.re · 15/11/2024

Playing around with a low-cost helium stirling cryocooler. Not sure what to make of it yet, performance is... interesting. But it does make cold.

000

Andrey @spirit.re · 14/11/2024

Spent the day at the #electronica2024 expo(combined with Semicon 2024). Wow, what an event. They really do not exaggerate that you're going to walk 26km. Felt like a kid in a candy store the whole time I was there. Highly recommend going in 2026 if you can make it.

000

Andrey @spirit.re · 12/11/2024

Just noticed that a few people followed me on here. Hi, I'm not dead, just working on stuff. I'll post a fun teardown soon-ish.

000

Andrey @spirit.re · 28/07/2024

I've always wanted to make a charging-free, perpetually running 96%-size wireless keyboard, and the first step towards that is to figure out if solar cells can be cut into intricate shapes, to be fit on the backplate, all around the keys. The answer: yes, with lasers of course! youtu.be/ioT79EGXvYY

youtu.be

Solar cell cutting video

010

Andrey @spirit.re · 27/07/2024

I decided to try making my own wireless headset, mostly because very few of them out there meet my highly specific requirements. To start, I made a kevlar headband with integrated wiring and antenna. Here's the process(🧵). I cut some fabric and threaded all the wiring through.

Several rectangular strips of kevlar fabric laid out on a table

One strip of kevlar fabric, with teflon-coated wires woven through it in a checkerboard pattern

100

Andrey @spirit.re · 12/07/2024

I needed to have more than 2 SIMs on standby to receive important notifications, but all solutions on the market were, at best, very shady. So I made my own using a cheap Android smartphone. It's opensource, and very low quality! github.com/Spirit532/SM...

010

Andrey @spirit.re · 11/06/2024

This is the best Privacy Policy. And it's from a screensaver for Android! That doesn't need one! But Gооgle forced them to! www.jwz.org/xscreensaver...

jwz.org

XScreenSaver: Google Store Privacy Policy

XScreenSaver is a collection of free screen savers for X11, Linux, macOS, iOS and Android.

010

Andrey @spirit.re · 10/06/2024

Seems like the first wave of... something is upon Bluesky. I've been seeing hundreds of these zero-post, many-follower(botted) accounts popping up and asking for follows, most seem to be targeting a non-English-speaking audience. Looks like people get caught up in it too, but not unexpected.

000